| |
G8MNY > TECHNI 01.11.25 11:01z 62 Lines 3340 Bytes #179 (0) @ WW
BID : 44077_GB7CIP
Read: GUEST
Subj: Rotator Yaesu G250 info
Path: SR1BSZ<OK0NBR<OK2PEN<VK6HGR<ZL2BAU<GB7BED<GB7JED<GB7CIP
Sent: 251101/1010Z @:GB7CIP.#32.GBR.EURO #:44077 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (New Jan 06)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
This is small basic and reliable rotator with pot control and self hunting etc.
_
==º]³ Small Dia Stub
____________________________ º ³ Pole Clamps
/ ___ _ _ / ³ ==º]³
/ / _ \ __ / ³ ÚÄÄÄÄÄÐÄÁÄÄÄ¿
/ ³ (_) ³ / / / ³ 6 Wire _³___________³_ ROTATOR
/ \___ / /_/ / ³ Cable ³___________³
/_ _ _ _ _ _ _ _ _ _ _ _ _ / _.Ù ===º]|³ - - option flat
³__________________________³_.-' º |³ base plate
CONTROLLER Support U ===º]|³ remove bolts
Mast Clamps ÓÄÁÙ
DIAGRAM
NÄo/'oÄ¿ ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ*6*ÄÄÄÄÄÄÄ¿
)º( ÀÄ´<ÃÄÄÄÄÄÄ2K2ÄÄ´<ÃÄ¿ AC Common \ Thermal
240V )º( RUN// CW ³ ³ Trip
)º( 24V LED ÚÄo\ÄÄÄÄÂÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ*5*Ä())))Ä´
)º( ³ === 68uF 60v AC ===== ³MOTOR
)º ÀÄÄÄÄÄÄÄÄÄÄÁÄo/ÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ*4*Ä())))ÄÙ
³ º CCW
o º ÚÄÄÄÄÄÂÄ´>ÃÄÂÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄ120RÄÄÂÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
FUSE | º(12V _³_ ³ R ÚÄÄÄÁÄÄÄ¿ _³_ ³ +10V Cal1\³/
o º(___ /_\ ³ ³ ³ C W ³ 10V/_\' ³ ÚÄ3KÄÄ*1*ÄÄ¿
LÄo/'oÄÙ º( ³ ³ +16V³ _³_ ÀÄÄÄÂÄÄÄÙ ³ ³ ³ ³
on/off º(12V³ ³ ³ \_/ð ÃÄÄ¿NPN ³ 7³ 3 HEADING ³
³ ÃÄÄ)ÄÄ)Ä´>ÃÄ´ ³ON _³_ \³__ ³ 741/ÃÄÄ((()Ä>POT ³
EÄÄÄÄÄÄÄÄÙ_³_ ³ ³ ³ ³ /_\ e/³ ÃÄRÄ)ÄÄ<' ³ñ 200R ROTATOR
/_\ ÀÄÄ)ÄÄÄÄÄ)ÄÄÁÄÄÄÄÄÂÁÄÂÁÄÄÄÄ)ÄÄÄ´ 2 `\ÃÄÄ((()ÄÄÄ)ÄÄÄÄ*2*Ä>POT
³ ³ +³ _³_ e\³___³ ³ 4³ 2 RFC ³ 200ê
³ ³ === /_\ /³ ³ ³ ³ ³
³ ³ 100u³ ÃÄÄÙPNP ³ ³ ÀÄ3KÄÄ*3*ÄÄÙ
³ ³ ³ ÚÄÄÄÁÄÄÄ¿ _³_ ³ Cal2 /³\
³ ³ -16V³ ³ C C W ³ 10V /_\' ³ ³
³ ³ ³ ÀÄÄÄÂÄÄÄÙ ³ ³ -10V ³
ÀÄÄÄÄÄÁÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄ120êÄÄÁÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
(N.B. Incomplete diagram) * External Connections
DESCRIPTION
Two relays power the 2 pole AC rotator motor on either line 4 or 5. The Run LED
is lit when either is powered as either 24V AC or via the phase shift AC
capacitor. The relays are operated by the opamp and either driver transistor.
The opamp inputs are feed via RF filtering components with the bridge output,
comparing the slider voltage of the controller and rotator pots. The cal
presets enable calibration of ñ180ø positions (south).
IN USE
Although a very small rototor, I have used an enoumous 55el 23cms TONNA beam
5.5m long on one at 10m for many years. But to keep bearing strain down I use
only a 3cm x 30cm long stub pole.
Why Don't U send an interesting Bul?
73 de John G8MNY @ GB7CIP
Read previous mail | Read next mail
| |